One City One Hire is an innovative economic development strategy that serves as a catalyst to jump-start the Mayor's pledge to put all unemployed District residents--in every Ward of the city--back to work.
Energy Tips for Institutional and Government Buildings
- Adjust your thermostat. In the summer, set your thermostat to 78 degrees when the work place is occupied, and 85 degrees or off after business hours. In the winter, set your thermostat to 68 degrees when the work place is occupied, and 60-65 degrees or off after business hours. You can save up to 3% for each degree the thermostat is raised in the summer and lowered in the winter. Using ceiling or room fans improves air circulation.
- Reduce your lighting. A general rule is that a light should be off when no one is present. Turn off lights in unoccupied areas, remove excess lighting and turn off signage and other lights not necessary for security and safety.
- Be energy smart with office equipment. Turn off office equipment or set it to "power down" when not in use. Setting computers, monitors, and copiers to use sleep-mode when not in use helps cut energy costs by approximately 40%. Remember to turn equipment off at the end of the workday.
- Use shades and blinds. On hot days, draw the curtains and/or shades to keep the sun out. Remember to close doors to the outside to keep in cooler air.
- Install efficient lighting. There are a number of low-cost solutions that can be invested in to make lighting much more efficient and save money in the long run. For example: replace incandescent bulbs with compact fluorescents, which can last up to nine times longer; upgrade fluorescent lighting fixtures to high efficiency equipment; replace incandescent lights in exit signs with LED fixtures. This can reduce costs of these signs by up to 95%.
- Install programmable thermostats. Programmable thermostats or time clocks can automatically control temperature settings and save energy.
- Use "smart" power strips. These sense the presence or absence of office workers and turn the attached equipment on or off accordingly.
- Maintain your HVAC system. Perform regular maintenance to keep your heating and air conditioning systems running more efficiently.
Building and Design Tips
- General cooling measures. Think about using "green" design features. Use evaporative cooling wherever possible. Attempt to use natural ventilation and light surfaces. Encourage daylighting of interior spaces in the design. Surround all buildings and cover parking lots with trees to reduce local environmental temperatures. Specify light-colored aggregates for local access road and sidewalk pavements.
- Landscaping and use of shade. Combine architectural features and shading so that a minimum of the building envelope is exposed to the sun. Design landscaping around the building and over parking areas so that no parking area is exposed to the sun. This will not only reduce the heat build-up in parked vehicles, but will reduce the temperature of air blowing against the building by 6 to 8 degrees.
- Combined heat and power systems. Often there is a balance between the heat requirements of an institution and its electrical needs. This energy match means that the waste heat from a small electrical generator can be used to generate electricity.
- Solar power on rooftops. Consider installing solar electric collectors and/or solar hot water collectors on the roof. Ensure that the building design includes adequate support for the dead weight load and the wind stress, and all conduits for pipes or wires.
- Water, gas and ventilation. Design a gray water collection system for irrigating landscaping. If natural gas is unavailable, consider ground source heat pumps. Design public space ventilation to respond to occupancy needs with such features as carbon dioxide detectors. Avoid air curtains that allow air leakage from conditioned spaces. Pressurize and test all ducts for leakage before dropped ceilings are installed.
- Engineering requirements. Be sure that Performance Assurance or building commissioning is included in the engineering services provided by the engineer
- Retrofit lighting. Convert T12 lights and magnetic ballast to T8 lights and electronic ballast. Install occupancy sensors, which can reduce lighting costs by up to 40%. Convert hallway and non-public security lighting to energy saving 25-watt T12 bulbs. Convert TV surveillance cameras to newer equipment, which may not require floodlighting.
- Weatherize buildings. Install awnings, solar shade screens or sun-control film for windows, and apply a heat-blocking coating to your roof.
- Install an Energy Management System. An EMS will control heating, ventilation, and air conditioning equipment and lighting systems automatically to maximize efficiency and savings.
- Buy ENERGY STAR products
- ENERGY STAR certified equipment and products use less energy than other products, save money on utility bills, and help protect the environment. Establish a policy of only buying ENERGY STAR certified equipment such as computers, monitors, and printers.
Special Tips for Schools and Large Facilities
- Sensors, timers, and control mechanisms can increase efficiency by responding to occupancy patterns that may vary dramatically during the day. These can be used for lighting, appliances, and temperature controls for air and water.
- Choose an energy monitor for your classroom every week who will make sure that energy is being used properly.
- Start an "Energy Patrol" at school and at home.
- Combined Heat and Power (CHP) systems are a viable option for reliable energy and hot water. An Energy Management System (EMS) can accommodate changes in ventilation needs and increase efficiency. The HVAC system should be able to respond to occupancy changes and not waste energy when rooms are empty.
Museums, Libraries, and Other Public Facilities
- An Energy Management System is a viable option in buildings with regular hours. Timers and sensors can respond to occupancy as needed. HVAC systems, too, can respond to occupancy with carbon dioxide sensors to increase efficiency.